superplasticizer "polyplast sp-1" (analogous to c3)

Consumption

Mix thoroughly before use. For concrete: 0.6-1.3 l per 100 kg of concrete. Concreting comes down to the use of a cast mixture, which easily fills a mold or formwork and forms a flat, smooth surface that does not require finishing. For mortar: 0.3-0.6 l per 100 kg of cement. The use of a plasticizer for plastering inclined and vertical surfaces is possible if it is added no more than specified above. If the concentration of Superplasticizer S-3 is greater than specified, the solution may slip.

Technical specifications

Superplasticizer S-3 is produced in the form:

• 1) coffee-colored liquids with a viscous consistency in canisters of 20, 10, 5 l or in containers from 0.5 to 10 l;
• 2) brown powder in plastic bags 0.8-25 kg.

The characteristics of the C3 plasticizer are given in the table.

The use of a plasticizer provides the concrete mixture with:

• increasing frost resistance and mobility of the composition to P-5;
• increase in strength by 40%, which corresponds to class B45;
• slower setting during long-distance transportation;
• reduction of shrinkage;
• increase in adhesion with reinforcement by 1.6 times, and water resistance up to W12.

Storage and transportation conditions

Store in a tightly closed container at a temperature from -5°C to +30°C, protecting from moisture, heat and direct sunlight. Transport at temperatures from -40°C to +30°C, by all means of transport, in covered vehicles; after defrosting and mixing, the properties are preserved. Defrost at room temperature. Shelf life and storage: 24 months from the date of manufacture, subject to compliance with transportation and storage requirements. Ingredients: water, plasticizer S-3, antiseptic.

Guidelines for using the supplement

Every year, the construction industry uses 36 thousand tons of this substance, which is combined with retarders or accelerators, water repellents, which makes it a universal tool in the production of concrete mixtures.

You must carefully follow the instructions for use of the C-3 plasticizer.

Method of using dry plasticizer

This additive is added to the cement-sand composition in a liquid state.

How to dilute plasticizer C-3 - the powder is indicated in the product data sheet. To prepare concrete with this additive:

1. Gradually mix water with powder in a clean container to a concentration of 15–35%, taking into account ease of use, operating conditions, and technology requirements. To speed up the process, the recommended liquid temperature is +30 - +90 °C. The consumption of S-3 plasticizer for preparing 1 kg of such a solution is 366 g, and water - 634 g.
2. Leave the resulting compound for 24 hours, then add it to the container along with the main liquid and other ingredients when the concrete composition is mixed.

Method of using watery superplasticizer

Depending on the amount of additive in concrete, its setting time depends. Before adding the plasticizer, it should be mixed in a clean container until smooth. According to the instructions for the plasticizer for concrete S-3, it is dosed at the rate of:

• About 5-1 liters per 100 kg of Portland cement for the construction of floors, ceilings, and walls;
• 1-2 liters per 100 kg of cement mixture for the manufacture of monolithic structures and foundations.

The liquid additive is poured along with water while the concrete mixer rotates. Then other fillers are added and the solution is prepared until it is ready.

In private housing construction, the question often arises: how much C-3 plasticizer is needed for a bucket of cement. The answer is simple: 0.05-0.1 l.

When preparing concrete with the addition of a superplasticizer, you should follow the instructions for its use. Only in this case, ready-mixed concrete and building structures will receive the corresponding positive characteristics and advantages over other products.

Precautionary measures

When working with the additive, use personal protective equipment: glasses, gloves. In case of contact with skin, rinse with plenty of water. In case of contact with eyes, rinse immediately with plenty of water and consult a doctor. Keep away from food.

Cleaning containers and tools: after completion of work, the equipment must be freed from residual material and thoroughly washed with water or soapy water.

Waste disposal: Empty containers are tightly closed with lids and taken to household waste collection points.

Plasticizer S-3 dry, 20 kg

Plasticizer S-3, in accordance with GOST 24211-08, belongs to the class of superplasticizing (OK up to P5) and superwater-reducing additives for concrete and mortars. Additive Fort Plasticizer S-3 consists of a mixture of modified high-molecular sodium polynaphthalene methylsulfonates. This additive is used in the production of a wide range of reinforced concrete products, ready-mixed concrete, lightweight concrete, construction of monolithic structures, as well as in the production of small-piece concrete products.

Using Form Plasticizer S-3 will allow:

• obtain cast self-compacting concrete mixtures that require virtually no vibration during installation;
• reduce the water-cement ratio of the mixture by 20% or more (water-reducing effect), thereby obtaining a significant increase in strength, water resistance, frost resistance, density, etc.;
• reduce cement consumption by up to 22% (in equal mobility mixtures);
• simultaneously obtain concrete mixtures with increased mobility (P3-P4) compared to a composition without additives and increase the strength of concrete by reducing the water-cement ratio;
• reduce time and energy costs for HTW of concrete products;
• produce ready-mixed concrete while maintaining mobility without delamination and water separation, followed by pumping and placement into formwork.

Application

Fort Plasticizer S-3 is used for:

• production of all types of concrete class B15 and higher, incl. with prestressed reinforcement;
• production of concrete mixtures for architectural forms and paving elements;
• monolithic housing construction;
• production of densely reinforced, thin-walled reinforced concrete structures.

Fort Plasticizer S-3 does not contain substances that cause corrosion of reinforcement and does not contribute to the formation of efflorescence.

It is recommended to add the additive Fort Plasticizer S-3 to the concrete mixture in the form of an aqueous working solution (the dry additive is pre-dissolved with water) together with mixing water. After addition to the concrete mixture, it is recommended to provide sufficient mixing time to ensure uniform distribution of the admixture in the mixture. The mixing time is also selected by the consumer based on the technology conditions. The effectiveness of a concrete additive directly depends on the chemical composition of the cement and the quality of the aggregates.

When changing the inert or binder of a concrete mixture, it is recommended to adjust the composition of the mixture in laboratory conditions.

Dosage: 0.5 - 0.8% dry matter by weight of cement.

Other dosages are possible. The optimal dosage is determined by checking the effectiveness of its administration in accordance with GOST 30459-08.

Packaging, storage, transportation

Polypropylene bags with a polyethylene liner of 20 or 25 kg, barrels, cube containers. Transported by any means of transport (non-dangerous cargo). Store in unopened original packaging in a dry place on pallets, protected from direct sunlight and freezing. Shelf life - 12 months from the date of manufacture (see date in the quality certificate).

Characteristics of superplasticizer S-3

Plasticizers for cement mortars are produced according to TU 5730-012-97474489-2010. Before you start using them, it is important to familiarize yourself with the technical features of the supplement. So, in appearance it is a homogeneous powder, which according to the norm should have a light brown color. The mass fraction of water in the substance should not exceed 10%. As for the activity of hydrogen ions, this indicator should be equal to 8.5 + 1.5, which is true for a 2.5% aqueous solution. Chlorine, or rather, its mass fraction should not exceed 0.1%, which is true for a substance that is in a dry state.

If you have started producing tiles, then you may need a plasticizer for tiles; it is added during the production of the top layer of products.

Superplasticizer S-3 Optiplast series Optimist S409 for you wholesale at a competitive price

Superplasticizer S-3 Optiplast of the Optimist S409 series is used in the production of monolithic and prefabricated reinforced concrete products and structures from heavy, light and cellular concrete in any type of construction, including in the manufacture of products and structures of drinking water supply systems.

Optiplast is used in the construction of critical monolithic structures with a high degree of reinforcement and complex configuration. The introduction of superplasticizer S-3 Optiplast into concrete increases the mobility of the concrete mixture from P1 to P4, reduces cement consumption by up to 20% and slows down the setting time while accelerating further strength gain.

At the same time, the final strength characteristics of the structure increase up to 50%, the water requirement when mixing the binder decreases by 20-28%, the adhesion of concrete to embedded reinforcement and metal products increases by 1.5-1.6 times with simultaneous inhibition of the metal surface.

With the introduction of superplasticizer S-3 Optiplast, it is possible to obtain “cast” concrete with increased water resistance and crack resistance, and reduce energy costs (with vibration, HME) by 30-50%, and in some cases completely eliminate additional energy costs. Today you can very profitably purchase from us in bulk the effective Superplasticizer S-3 Optiplast of the Optimist S409 series by sending a request to [email protected]

Concrete superplasticizer S-3 Optiplast of the Optimist S409 series is ideal in combining its abilities and favorable price!

Characteristics and properties of superplasticizer S-3 Optiplast

The composition is a non-toxic, environmentally friendly, ready-to-use liquid. It is odorless, does not emit harmful gases or vapors during storage and has no effect on the human body. Superplasticizer S-3 is easily mixed with other additives (hydrophobizers, accelerating, retarding, air-entraining agents), without entering into a chemical reaction with them and maintaining its properties.

Superplasticizer consumption is 150-200 ml per 1 bag (25 kg) of construction cement-sand mixture or 1.5-2.5 liters per 100 kg of cement. The superplasticizer retains its properties when heated to +40C +45C, and when frozen it does not reduce quality indicators. Before use, the aqueous solution must be heated to a temperature above +10C and mixed thoroughly. Precipitation during storage is allowed.

Your profitable purchase of superplasticizer S-3 Optiplast

By purchasing Superplasticizer S-3 Optiplast, Optimist S409 series from us in bulk and in large wholesale, you are guaranteed to receive the most favorable price and a product of guaranteed proven quality. You receive fast delivery of the material to the site in any region of Russia and save your costs, gaining real quality in return.

Back to “Antiseptics, impregnations, water repellents and plasticizers”